Petite dentelle d’été NGC6992

Voici sans prétention aucune un petit traitement que j’ai fait cet après-midi. Il s’agit de la nébuleuse NGC6992 réalisé cet été chez mes parents.
J’ai eu beaucoup de déchets et je suis déçu de mes acquisitions.
Il en résulte une photo avec une FWHM de 6″ :(((
J’ai seulement 3 poses de 300s en BIN1 avec le filtre L devant le capteur de l’Atik 383L+ refroidi à -20°C, sur la FSQ106. guidage par Lodestar sur DO Atik OAG.

J’ai réalisé l’ensemble du traitement avec Pixinsight en suivant les conseils de maître Philippe :)

NGC 6992 - A. BERNARD FSQ106 Atik383L Atik OAG EFW2 3x300s L  -20°C en bin1
NGC 6992 – A. BERNARD FSQ106 Atik383L Atik OAG EFW2 3x300s L -20°C en bin1

SH2-157 et Bubble Nebula en RVB

Après plus d’un mois d’essais divers et variés, voici enfin la version couleur de la photo que j’ai prise le 15 septembre à Parnes.
Rouge : 7 x 300s
Vert : 7 x 300s
Bleu : 6 x 300s
61 Dark de 300s
21 Flats
9 offsets sélectionné manuellement (seuil inférieur à 1000).

Je n’ai pas mis la couche de luminance pour le moment mais je verrais ça un peu plus tard.
Je la reprendrait encore une fois pour enlever la trainée de satellite qui se trouve sur une image rouge et pour enlever les pixels chauds que j’ai encore du mal à enlever. Ah ce satanée capteur Kodak KAF >:|

SH2-157 + Bubble Nebula en RVB - Alban BERNARD
SH2-157 + Bubble Nebula en RVB

SH2-157 et la bulle

Voici la grande nébuleuse SH2 – 157 en forme de pince qui se trouve dans la constellation de Cassiopé. Elles est distante de 8154 années lumières. Sa taille est de 213,6 années lumières.

En haut à gauche se trouve la nébuleuse dite de la bulle (Bubble Nebula) qui est référencée dans le catlogue NGC sous le numéro 7635 dont l’étoile centrage est de magnitude 8,7.

les infos de prise de vue :
Lum : 7 x 600s
Rouge : 7 x 300s
Vert : 7 x 300s
Bleu : 6 x 300s (j’ai enlevé une photo car trainée d’avion)
23 Dark de 600s
61 Dark de 300s
21 Flats
9 offsets sélectionné manuellement (seuil inférieur à 1000).

SH2-157 et Bubble Nebula (NGC 7635)
SH2-157 et Bubble Nebula (NGC 7635)

Lune et Vénus

Hier soir j’ai fait un peu d’astro et j’ai commencé par shooter la Lune et Venus. Les deux astres dans le champ du 5D avec la FSQ !

Lune et Venus au Canon EOS5D sur FSQ106
Lune et Venus au Canon EOS5D sur FSQ106

La comète GARRADD C2009P1

Voici une petite photo de la comète  GARRADD C2009P1 qui se trouve actuellement dans la constellation de la Grande Ourse. Malheureusement, elle n’est visible ni à l’oeil nu ni même aux jumelles.

Alors je lui ai tiré le portrait avec ma config astro traditionnelle : Caméra Atik 383L+ sur lunette astronomique Takahashi FSQ106. Guidage avec la caméra StarLight Lodestar sur lunette Skywatcher 80/400. Le tout posé sur ma monture equatoriale allemande Skywatcher EQ6 révisée et customisée par mes soins en 2009 et 2010.

La comète GARRADD C2009P1 avec Atik 383L+ sur FSQ106
La comète GARRADD C2009P1 avec Atik 383L+ sur FSQ106

Lakeside Astro Motorfocus System

Pour mon anniversaire ma famille m’a offert un système de mise au point informatisé pour ma lulu Takahashi FSQ106N.

Compaticle 100% ascom, il gère aussi la compensation de température.

Lakeside Astro Motorfocus System
Lakeside Astro Motorfocus System

 

System components:

  • Control unit with 16×2 LCD display, push buttons and internal temperature sensor
  • Stepper motor and gearbox with 4000 steps per revolution
  • Bracket to connect stepper motor assembly to the telescope
  • Shaft coupler
  • RS232 cable (2 metres long)
  • Stepper motor cable (2 metres long)
  • 12v DC power cable (2 metres long)
  • Required screws etc. for fitting
  • Installation & user guide CD

Requirements for autofocus:

  • PC running Windows XP, Vista or Windows 7
  • ASCOM V5 or above
  • Microsoft .NET V2 or above
  • Suitable ASCOM compliant programs such as MaxIm DL, CCDSoft and FocusMax
  • Serial port (or USB port with suitable USB to Serial convertor)
  • 12v DC power supply rated at 1 amp or better

Control Unit:

BoxThe control unit is a sturdy die-cast aluminium box fitted with a 16 character by 2 line LCD display and three push buttons. The unit is fully ASCOM compliant for use with programs such as MaxIm DL and FocusMax etc., and has been tested with Windows XP, Vista and Windows 7.

The unit has a professionally made high quality printed circuit with full silk screen and solder mask for long term reliabilty.PCB

The display has a variety of uses which can be accessed via the three push buttons. The centre button is used to select the various modes whilst the outer two buttons are used for manual control or for setting the parameters of the system. The modes available are AUTO, MANUAL, PRESETS, SETUP and TEMP.

The default mode is AUTO which is used for autofocus using any suitable ASCOM compliant programs such as MaxIm DL, CCDSoft and FocusMax etc. The focuser position is shown on the LCD display in this mode.

When in MANUAL mode the motor can be driven using the buttons on the unit. When a move IN/OUT button is pressed the motor speed starts at a low rate to enable precise positioning and ramps up to maximum speed if the button is held down. The LCD display shows the focuser position at all times. When in manual mode it is possible to set a backlash value.

The PRESETS mode allows you either save up to three positions or goto one of the previously saved positions. This could be useful if you are using the unit in manual and swapping eyepieces or imaging equipment which have different focus positions.

Also provided is a special routine for ‘parking’ the focuser which could be useful if you are using a mobile setup. This will allow you to move the focuser to a preset position, e.g. with the tube fully closed for packing away the telescope. Whenever the ‘park’ command is initiated it automatically saves the original position so that on subsequent use the focuser can be returned to that position using the ‘unpark’ command.

The SETUP mode provides on screen access to routines to allow you to calibrate the system or to select step size, direction of movement and the backlash for manual use.

The TEMP mode will display the temperature from either the internal or optional external digital temperature sensor. The temperature will also be displayed in programs such as MaxIm and FocusMax.

Temperature tracking is now provided which will work with all the usual programs such as MaxIm DL and Focusmax to automatically adjust the focus position to compensate for temperature changes. It is recommended that the external temperature sensor option is used for better performance.

Stepper Motor Assembly:

FTThe motor assembly consists of a stepper motor and gearbox with a custom bracket and shaft coupler to suit the users telescope or focuser, shown here attached to a 3.5″ FeatherTouch Focuser.

A selection of standard brackets and couplers are offered to fit a variety of telescopes and new brackets are always being added to the range. We would be happy to provide non standard items on request.

 

External temperature sensor

The control unit is wired to use either the internal digital temperature sensor or an optional externally mounted sensor. The external digital sensor needs to be soldered to the 9 pin ‘D’ type connector on the motor bracket. The sensor is fitted with flying leads so that it can be placed exactly where you want it on the telescope.

Use of the internal or externally mounted sensor is selected by jumpers on the printed circuit board in the control unit. Note that temperature compensation is not offerred with the unit at this time but may be added later if there is demand for it. Use of the temperature sensor will, however, permit logging and display in programs such as FocusMax.

 

Commandé chez IanKing Imaging en Angleterre, je l’attend dans la boite aux lettre la semaine prochaine.

La nébuleuse de la tête de cheval : IC434

Hier soir, c’était pleine [pleine lune] mais le ciel était clair.

J’ai donc décidé de tester mon Setup, FSQ106N sur EQ6 custom avec guidage par Lodestar sur lulu 80/400 avec PHDGuiding en pose de 2s.
J’ai fait ça avec mon Asus EeePC et ça marche alors qu’avec mon portable Fujitsu ça fonctionne pas.

Bref, 8 poses de 600s en Bin2 à -20°C sur 9 (1 superbe trainée d’avion que j’ai jeté).
Dark, flat et offset, tous fait avec le logiciel Atik.

Et ça donne ça, traitement sous PI puis courbe et niveau sous PS.

 

IC434 La nébuleuse de la tête de cheval - Alban BERNARD
IC434 La nébuleuse de la tête de cheval - Alban BERNARD